Automotive hail repair in Macungie, PA: The two techniques mentioned above will remove the majority of hail damage on your car, but a professional job at your local auto body shop is recommended for deep dents or badly damaged surfaces. The services tend to be cheap, fast and rarely require a new paint job. However, it is a good idea to compare prices and offered services at various body shops to see which package works best for your wallet and car’s situation.

In the first place let’s begin with some car paint care tricks: Another way to fix the small dents is parking your car in a sunny area. This is an effective way that most of car enthusiasts all know. By doing this way, the metal will heat up and expand. As the car surface expands, the shallow and light dents will pop out. The longer you park your car in a sunny area, the more likely this way will work.

Wax Your Car: Yes, I think it is accepted knowledge that your car needs to be waxed on a regular basis. If you have just bought a new car from a dealership, you must realize that no new car comes with wax from the manufacturer or dealer. New car prep does not mean the dealership is going to wax your car either. So that new car paint of yours is like taking a new-born child out in the sun with no sunblock on their skin. You can review my selection of best car waxes in helping you choose a quality car wax. Just remember your car should be waxed every 4-6 months under “normal” conditions. If you live in extreme weather conditions and you plan on keeping your car for over 5 years, you might consider applying wax to that new car paint even more frequently.

Use Hot Glue, Wooden Dowels, & Screws: When you attempt to take out dents yourself, you always put the risk that you might further damage your car, whether you make the dent worse or chip the paint. A safe way of trying to take out big dents on your car is by using several wooden dowels, a few screws, and a hot glue gun. Simply place two nails into each side of the dowel and put the hot glue on the bottom. Place the dowels glue-side down in areas around the dent, repeat as many times as needed to cover the area, let them dry, and pull each one out until the dent is gone.

Fixing Scratches: Apart from rust-proofing the vehicle, you should fix small scratches promptly. If the scratch is not too deep, you should only use touch up paint and finish off with a rubbing compound to get a good shine. If the scratch is deep and exposes the metal, you will have to sand off the surrounding paint and apply primer before painting the affected area. Find more details at Auto Repair Colorado Springs.

The first step to performing a dent repair without using paint involves assessing the dent itself and determining if a paintless dent repair is even possible. According to most experts, 80 to 90 percent of dents can be repaired using PDR techniques. However, there are a certain percentage of dents that are impossible to repair without following it up with a paint job. The following types of dents usually fall into this “non-PDR” category: Very deep dents – Even very large dents can be repaired using PDR if the dent is fairly shallow. However, if a dent of any size is pushed in too far, the metal can’t be bent back into place without damaging the paint and requiring repainting.

First, you have to pick a proper tool kit. And that’s not easy for a user who has little clue what’s going on. Some of them are cheap — low prices should raise red flags. Others are so expensive (three-figures or more) that they’re probably right up there with the cost of a decent professional repair (although, to be fair, if you buy the kit you can perform multiple repairs). Many of the high-end, expensive tools are intended to be used along the inside of the panel, much like a pro would do. (Gaining access to the inside of body panels can be a chore, though, and often involves careful removal of multiple interior trim pieces.) Alternatives (which tend to be the less expensive kits) flaunt the conventional wisdom that small dents should be massaged back out from behind the painted surface. These options instruct the user to glue a tool to the dented surface and then twist or pull on the tool to pop it out. True, you can go buy the same tools as a pro, but it takes a lot of skill and experience to use them properly.