Paintless dent repair: This technique is popular among automotive enthusiasts when it comes to the removal of small dents. The idea is simple: heat will inevitably cause the metal surface to expand and (hopefully) pop the dent out. Remember that the more time the car spends time under the sun, the better this technique will work. Use a plastic and/or leather conditioner for the car’s interior, so as to not damage it while exposing the car to maximum sunlight. If the sun’s heat isn’t particularly strong that day, a simple hair dryer could be used in conjunction with the sun to concentrate the heat to a specific area. Point the hair dryer to the dented area for two-minute intervals until the dent pops out. Be careful not to touch the hot lip of the hair dryer on any painted surface. A two-to-four inch gap between the dryer and the surface is recommended.

1st let’s begin with some car paint care advices: If you can not expose your car to the sunlight, you can use a hair dryer instead. Just aim the hair dryer to the areas you want to fix, and wait until the dents even out. The ideal distance between the hair dryer and the car should be 2-4 inches. While using a hair dryer, there should be an interval of 2 minutes. If the car’s paint starts discoloring, you should stop applying heat right away. Use a rubbing compound or wax to revise the paint color.

I don’t care if you wash your car yourself (more on that strategy later in this page) or you take it to a quality car wash. (Yes, not all car washes are created equal) This is not an option as dirt is your #1 enemy when it comes to the finish on your new car paint. And this doesn’t mean once every 6 months whether it needs it or not. This means regularly and consistently. (A minimum of once a month…minimum!)

Another popular method for removing car dents out of plastic material involves using two popular household products: a hair dryer and compressed air. Start off by heating the car dent with the hair dryer at its highest temperature, which will expand the plastic of the car. As soon as it’s hot enough, grab the can of compressed air, turn it upside down, and begin spraying that same area. Since the cold air will cause the plastic to contract, the dent will pop out.

Clean the Car. One of the most important things you can do to maintain the exteriors of your car is to wash and shampoo the vehicle regularly. Commercial power washes are also beneficial if you use them every few months. Make sure you keep a good distance between the surface of the car and the pressure jet, so you don’t damage the paint. If you’re unsure you could get it done professionally. See additional details at Auto Decals & Lettering Colorado Springs.

If you are considering learning the skill of how to do paintless dent repair, it’s important to understand that it isn’t simply a matter of “popping” a dent out and expecting that the body will be perfect again. PDR involves a very slow and methodical process that requires special tools, a certain level of knowledge and skill, and a great deal of patience. Some dent repairs, even on small dents, can take up to two hours.

So, we’ve explained what the procedure looks like — assuming it was done properly. And as you could probably guess there are a lot of ways an amateur or first-timer can get it wrong. It’s different than most other car repairs because it’s not about mechanical prowess; it’s more about control and the ability to maintain a steady hand and a gentle pace. You can’t rush it. The problem is, once a sheet metal repair starts to go awry, you’re usually much, much worse off than if you’d just left it alone. Metal holds its shape, but only to a certain point. Let’s say you get a dent in the hood — nothing too drastic, just a shallow, even dent with no sharp creases in an area that’s pretty easy to reach. You think it’ll be easy to pop it out on your own, so you begin to massage the underside while holding your shaping tool in place. You’ve made good progress so far, and a casual observer wouldn’t even notice the flawed area. But it’s not exactly perfect, and since it’s been fairly easy to this point, you decide to keep massaging the area to make it flawless. After a few more minutes of massaging, you realize that you’ve pushed it just a little too far. And now you’ve got this flabby area on the hood where you stretched out the metal. And there’s no easy way to shrink it back down. Keep going and it’ll stretch even more. Lesson learned.