Double side planer factory by v-holdmachinery.com: The defining characteristic of all machine presses is that they press a work-piece using high pressure to change its shape. While the exact mechanics vary depending on the type of machine press, most machine presses work by pressing a plate or die onto or against a work-piece. The work-piece can either be manually placed into the machine or a through-feed will automatically place the work-piece in the correct position. Once in position, using hydraulics pressure, the machine press pushes the plate or die against the surface of the work-piece, which causes the work-piece’s shape to deform into the shape required by the manufacturer. See extra details on 2 sided planer.

The radial arm saw is pretty much a portable circular saw that glides on an adjustable arm suspended over a fixed cutting surface. The blade and motor are connected to the arm by a yoke, which is adjustable along both horizontal and vertical planes, enabling the saw to be swung in a variety of directions. For cross-cut work, position the board flush with the fence at the rear of the saw and draw the blade across the wood. The bevel lock allows the saw to be tilted for cutting angles. You can set it to the desired angle using the protractor on the saw housing. The saw can be swivelled right or left for mitring, or turned a full 90 degrees for ripping. The blade can also be raised or lowered using a crank. The size of the saw is determined by the dimension of the blade the saw can accommodate. As an example a model using a 10 inch blade would be able to cut work-pieces up to 3 inches thick.

Composite presses deal with composite materials that need to be shaped into a usable product. The automotive trade use them to shape carbon fibre panels and battery boxes for electric cars. The aero space industry use them for shaping light weight panels and seat covers. The military use them to create bullet proof floor pans for military vehicles. The refrigeration industry use them to create cold storage insulation panels for fridges. The job of a laminate press is to bond layered materials together to create a stronger material than the original, and also for cosmetic purposes. Many laminating processes involve coating a film, plastic, metal, wood, or other substrate with a surface to strengthen it to be used for a much broader range of purposes.

A mortise is a square slot cut in the direction of depth for the purpose of making a mortise and tenon joint in a wooden piece. The mortising woodworking machines are used for cutting mortise and tenon joints which are very laborious and time consuming operations. There are three types of mortisers, namely (1) hollow chisel mortiser (2) chain mortiser and (3) oscillating bit mortiser. The hollow chisel mortiser, the most commonly used woodworking machines, consists of a revolving spindle carrying an auger bit at the bottom end. The auger bit rotates at a high speed inside a hollow chisel of square section. When the chisel is forced into the wood, the bit bores a square hole by the sharp end of the chisel, the auger bit and chisel thus work together and perform boring of a square hole. The depth of the mortise is regulated by means of an adjustable depth stop. The spindle is rotated by an electric motor, and tool-feed is obtained by pressing foot-lever.

The band is available in two models, vertical and horizontal. In the former, two wheels are arranged side by side and the table is mounted underneath. In the latter model, Frame illustrated in Fig. 10.55, the wheels are arranged one above the other in a vertical plane below the table and the band passes through the table. As in the case of the circular table, angular cuts are obtained by tilting the saw table. The size of the band saw is specified as the distance from the saw band to the inner side of the frame. The distance is roughly equal to the diameter of the wheels.

A drill press is simply a fixed in place version of a hand drill, it’s great for precise work. With an adjustable table beneath the chuck with a hole in its centre, a spinning drill bit can pass cleanly through a work-piece. Drill presses come as either freestanding floor models or for worktops. The drill press is powered by an electric motor, driving it via a system of pulleys or gears. The drill bit is locked into the chuck, then driven down using a hand powered lever system, and a spring pushes it back up when pressure on the lever is released. A number of adjustments including a moveable table depth, a depth gauge to set the distance the spindle travels and pulley adjustments to change speeds increases the tools functionality. Read even more details at https://www.v-holdmachinery.com/.

After 20 years development, V-HOLD has constructed strong hardware facilities and humanized management system by bringing in tens of brand-new large automotive precision CNC machine center from developed countries such as Japan, German, along with over 67,000m2 large modern workshop with complete facilities and production lines, V-HOLD has realized its high efficient production. Besides that, the cooperation with world famous management consulting firm and introduction of modern business administration system such as ERP, 6S have laid solid foundation to the development of V-HOLD. Thanks for the trust and support of our customer. V-HOLD will consistently stick to the belief that: Profession and concentration accomplish excellent brand !